Do not forget to close the sealing cap after replenishing oil and leave the filling filter inserted in the filler neck,. Before opening the equipment it is therefore necessary to undertake all measures. With regard to the environmentally correct disposal of waste oil and, if applicable, of cleaning agents, contact. We shall not assume any liability for damage and operational interruptions resulting from incorrect operation.
The oil must not form any resinous, sticky, solid or corrosive deposits. Different oil qualities, in particular. On the display 18 the oil. The oil outlet 1. The subassembly is supplied complete with an original instruction manual and original technical documentation. The subassembly may not be put into service until the machinery into which it is to be incorporated has been declared. The more familiar you are with this product, the better the results that you will be able to achieve with it.
Therefore we ask you: Please read these Operating instructions before putting the equipment into operation. It contains important information and references which have to be observed in using the equipment. Table of Contents Preface The Operator must ensure that the electrical installation, assembly, as well as the operation and maintenance is performed according to the pertinent specifications.
The electrical installation, as well as service operations at the electrical installation may only be performed by a qualified electrician, in compliance with the pertinent electro-technical regulations. Oil outlet 1 is equipped with an electronic function control to monitor the oil flow and must remain switched on at all times!
Please read the instructions in the settings and assembly sections. Do not forget to close the sealing cap after replenishing oil and leave the filling filter inserted in the filler neck, unless you perform any cleaning operations.
Before opening the equipment it is therefore necessary to undertake all measures to avoid discharge, e. With regard to the environmentally correct disposal of waste oil and, if applicable, of cleaning agents, contact the respective manufacturers or suppliers. We shall not assume any liability for damage and operational interruptions resulting from incorrect operation or improper treatment of the equipment. Instructions regarding oil The oil must be free of any undissolved substances.
Different oil qualities, in particular mineral and synthetic oils must not be blended. The oil quantity can be set separately for each oiling outlet to meet individual requirements from 0. On the display 18 the oil quantity per hour for all oil outlets or for one individual oil outlet is displayed when the machine is running.
The oil flow is monitored by the electronic function control The rotary lifting unit monitors the oil supply to the oil outlets. However when using all 24 nozzles the max. The exact amount of oil that is required to effiency lubricate the needles, sinkers and elements can be individually set for each of the oil outlets. Electronic monitoring of the oil flow to the outlets from the rotary lifting unit and oil flow to the nozzles.
The knitting machine is shut down and the fault displayed when the oil flow stops. Low consumption of oil, as the oil is directly applied to the designated locations.
No generation of oil mist to pollute the working environment. Low maintenance costs because the function requires no compressed. Low quantity of compressed air required for additional features. Possible additional fittings Needle head lubrication NKS. To lubricate the needle heads and latchinges with air-oil mixture. To flush the knitting elements with oil. After the oil, compressed air is blown through the spray nozzles. Automatic tank filling. An additionally installed float switch controls the level of the oil in the oil container via an inlet valve and thus the inlet volume of oil.
The nozzles have to be attachable in the near vicinity. Look for a suitable place at the leg of the knitting machine or in the machine control cabinet. The tubes have to rise continuously from the oiler to the nozzle. The highest point of each tube must be the nozzle. Moving camlock parts, needles sunkers and! The following nozzle installation is recommended: In the case of installing only one oil inlet per needle track all oil inlets can be located on in the same camblock.
Up to a machine diameter of 30" n only 1 nozzle per needle track or sinker track. From a machine diameter of 32" n only 2 nozzles per needle track or sinker track. Position the bore for the nozzles so that the oil jet falls directly on the foot of the needle or sinker.
It must not be deflected through any part of the camblock or sinker ring. Screw nozzles into the camblock segment until they are flush with the surface area T of the segment.
Secure nozzles with the lock nut U. Every pressure hose must have its highest point at the nozzle. This allows any air trapped in the oil to rise to the nozzle and be blown out, preventing any air pockets from developing in the hose which would impair the function. Only install angular nozzles in the dial camblock and the sinker ring. Cut the pressure hose 2 evenly to the desired length using the pipe cutter Art. Lay pressure hose in the machine. Blow out pressure hose using compressed air.
Starting off from oil outlet insert the pressure hoses in to the function control 10 one by one until the end stop is reached. Hawiwie Hawiwies. Filipe Alberto Magalhaes. CB Filtros. Eduardo Goes. Douglas Neves - Unax. Fernando Dan. Populares em Health. Antonio J. Jeice Oliveira. Alisson Casado. Thyago De Lima Vandresen. Ana Cristina. Paulo Sergio Dalvi. Liana Gomes Monteiro. Diorles Santos. Altair Lopes. Hiago de Souza.
Julio Cesar. Bruna Ramos. Fafnir Kesk. Elias Dias. Dificultad Principiante Intermedio Avanzado. Explora Documentos. Manual de Pulsonic 5. Cargado por Jack Michael Chang. Compartir este documento Compartir o incrustar documentos Opciones para compartir Compartir en Facebook, abre una nueva ventana Facebook.
Denunciar este documento. Marcar por contenido inapropiado. Descargar ahora. Carrusel anterior Carrusel siguiente. Material Complementario- 5s LeanSix Sigma. Buscar dentro del documento. Jack Michael Chang. Jhonatan Alegria Mendoza. Erika Copaja Cornejo. Popular en Science And Technology.
Diana Portilla. Jhon Guerra. Israel Rodriguez.
0コメント