Philips mp70 manual

Read these extensive report and overview by simply following the URL above Millions discover their favorite reads on issuu every month. Give your content the digital home it deserves. Get it to any device in seconds. Philips intellivue mp70 user manual. Publish for free today. All models can also use computer devices such as a mouse, a trackball and a keyboard.

The standard input devices for the MP30 are the Touchscreen and integrated navigation point; the MP20 is supplied with an integrated navigation point only. There is an optional built-in recorder. The standard input devices for the MP50 are the Touchscreen and integrated navigation point; the MP40 is supplied with an integrated navigation point only.

The IntelliVue family plug-in measurement modules can be connected to its. The IntelliVue family plug-in measurement modules can be connected to its FMS module slots with plug-and-play convenience. You can combine one each of the following modules in these slots: Pressure, Temperature, C.

Two of the same type of module cannot be used. You can also use the two-slot recorder module in the integrated slots. They offer both touchscreen and the Remote SpeedPoint as standard input devices. The MP80 can display up to 8 waves simultaneously and the MP90 up to 12 waves. The MP90 has the capability for two displays and can have a third main display with the D80 Intelligent Display. Power on LED. You then have three displays able to be configured individually and to be operated independently.

The Remote Alarm Device provides audio and visual indicators of alarms, in addition to those shown on the display.

Two color coded alarm lamps right-hand lamp flashes red or yellow for patient alarms, left-hand lamp flashes light blue for INOPs. Alarms off lamp - when illuminated it indicates that all alarms are deactivated.

Press to switch monitor on remotely. Press and hold for one second to turn monitor off. When using the monitor for transport directly after use on the docking station, insert the batteries before placing the monitor on the docking station. Related products extend the measurement capabilities of your monitor. They take their power from the monitor, and switch on automatically when you turn on the monitor. A green power-on LED indicates when they are drawing power from the monitor.

A permanently illuminated, or flashing, red LED indicates a problem with the unit that requires the attention of qualified service personnel. The flexible module server FMS lets you use up to eight plug-in physiological measurement modules. For individual modules, the maximum that can be used simultaneously in an FMS is: five pressure modules, four temperature modules, four VueLink modules. Use the MSL connector on the left-hand side to connect additional measurement servers.

Use the connector on the right to connect to the monitor. Available modules are:. You can plug and unplug modules during monitoring. Insert the module until the lever on the module clicks into place. Remove a module by pressing the lever upwards and pulling the module out. Reconnecting a module to the same monitor restores its label and measurement settings, such as alarms limits. If you connect it to a different monitor, the module remembers only its label. The connector socket on the front of each module is the same color as the corresponding connector plug on the transducer or patient cable.

When the setup menu is open, a light appears above the key. Some modules have a second key. On the pressure module, for example, it initiates a zeroing procedure. Depending on the monitor model, you can connect it to the monitor via a cable or mount it either on the left side of the FMS or on the back of the monitor, as shown here. Trend data and measurement settings from the measurements in the extensions are stored in the measurement server.

To separate an extension from the MMS, press the release lever down, and push the server forward. If the measurement server is removed during monitoring, the measurements from both the measurement server and the measurement server extension are lost. Everything you need to operate the monitor is contained on its screen. Almost every element on the screen is interactive.

Screen elements include measurement numerics, waveforms, screen keys, information fields, alarms fields and menus. The configurability of the monitor means that often you can access the same element in different ways. For example, you might be able to access an item through its on-screen setup menu, via a hard key, or via a SmartKey. These Instructions for Use always describe how to access items via an on-screen menu.

You may use whichever way you find most convenient. Pause Alarms - pauses alarm indicators. Pause duration depends on monitor. If pause duration is infinite, this key is labeled Alarms Off. Select again to. Silence - acknowledges all active alarms by switching off audible alarm indicators and. Select a screen element to tell the monitor to carry out the actions linked to the element. Note that the space between each line of a menu may be configured to wide or narrow to facilitate your most common method of operation, either touch, Speedpoint or navigation point, or mouse.

Select any item at the top of the Screen to open the Setup menu; scroll down the menu to highlight the element you want then press the navigation point to select the element. A padlock will appear on the Main Screen permanent key.

Silence - acknowledges all active alarms by switching off audible alarm indicators and lamps. Behavior follows the Pause Alarms permanent key. Main Screen - close all open menus and windows and return to the main screen. SpeedPoint knob - rotate and tilt to highlight elements. Press to select. Function keys on remote SpeedPoint - function identical to the first five SmartKeys configured for a. Rotate the SpeedPoint knob left or right.

With each click, the highlight jumps to the neighboring screen element. Alternatively, tilt the knob to move it in the direction of a screen element. A cursor moves across the screen, following the direction of the knob. Any screen element under the cursor is highlighted. When you reach the screen element you want, press the knob to select the element. Using the remote SpeedPoint, you can operate the monitor from a distant location such as at the foot of the bed. The remote SpeedPoint can be used with all monitors.

To use the navigation point, rotate it left or right. The element under the cursor is highlighted. If you are using a mouse or trackball, select screen elements by clicking on them press and release the left mouse button. While you are moving the mouse, a cursor appears and a highlight shows your current position.

A permanent key is a graphical key that remains on the screen all the time to give you fast access to functions. Pause duration depends on monitor configuration. A SmartKey is a configurable graphical key, located at the bottom of the main screen. It gives you fast access to functions. The selection of SmartKeys available on your monitor depends on your monitor configuration and on the options purchased. All waves and numerics disappear from the display.

All settings and patient data information are retained. A hardkey is a physical key on a monitoring device, such as the zero pressure key on the MMS or a setup key on a module. Pop-up keys are task-related graphical keys that appear automatically on the monitor screen when required. For example, the confirm pop-up key appears only when you need to confirm a change. Use this as you would a conventional keyboard.

Enter the information by selecting one character after another. Use the Shift and capital Lock keys to access uppercase letters.

Use the Back key to delete single characters, or use the Clr key to delete entire entries. Select Enter to confirm what you have entered and close the on-screen keyboard. If a conventional keyboard is connected to the monitor, you can use this instead of or in combination with the on-screen keyboard. You can use the on-screen calculator to perform any of the standard operations for which you would normally use a handheld calculator. When you switch the monitor on, it starts up in monitoring mode.

To change to a different mode:. Your monitor has four operating modes. Some are passcode protected. You can change elements such as alarm limits, patient category and so forth. When you discharge the patient, these elements return to their default values. Changes can be stored permanently only in Configuration Mode. These are for your information and can be changed only in Configuration Mode.

You must not change into Demonstration Mode during monitoring. These tasks are described in the Configuration Guide. During installation the monitor is configured for use in your environment. This configuration defines the default settings you work with when you switch on, the number of waves you see and so forth. When the monitor is in Demonstration Mode, Configuration Mode, or Service Mode, this is indicated by a box with the mode name in the center of the Screen and in the bottom right-hand corner.

Select this field to change to a different mode. The monitor enters Standby mode automatically after the End Case function is used to discharge a patient. Standby suspends patient monitoring. All waves and numerics disappear from the display but all settings and patient data information are retained. A special Standby screen is displayed. If a patient location is entered at the Information Center, this will also be displayed on the Standby screen availability depends on Information Center revision.

Your monitor comes with a set of preconfigured Screens, optimized for common monitoring scenarios such as OR adult, or ICU neonatal. A Screen defines the overall selection, size and position of waves, numerics and SmartKeys on the monitor screen when you switch on.

You can easily switch between different Screens during monitoring. Screens do NOT affect alarm settings, patient category and so forth. When you switch from a complex to a less complex Screen layout, some measurements may not be visible but are still monitored in the background. If you do not want to change the entire Screen content, but only some parts of it, you can substitute individual waves, numerics, high-res waves, or trends.

Be aware that these changes cannot be stored permanently in Monitoring Mode. Change HiResTrend , and then select the wave or numeric you want, or select the highresolution trend wave you want from the list of available waves.

If you do not see Change Numeric in the menu, this Screen may be configured to always display the numeric beside its wave. Changing the wave will automatically change the numeric.

In the Change Screen menu, the changed Screen is shown linked to the original Screen and marked with an asterisk. The ten most recently-used Screens including up to three modified Screens can be accessed. Modified Screens are still available in the.

If a modified Screen was the last active Screen when the monitor was switched off, it is retained unless Automat. Default is configured to Yes. A second display, showing the same Screen as the main display, can be connected to any of the monitors, for viewing only. The MP90 can have two main displays and additionally, as a third main display, the D80 Intelligent Display connected.

All main displays can be configured and operated individually using standard input devices. For MP90 monitors with multiple displays and multiple input devices, the usage and behavior can be configured according to specific requirements at installation for example, use for two independent operators or tracking of mouse input across two displays. For details refer to the Service Guide. When two operators are using two displays, the scope of an action depends on the type of operation:.

If you are operating two displays with one remote SpeedPoint, to navigate from one display to another:. The content of each Screen can be changed individually as described in the previous section. If you are operating two or three displays, you can choose Screens for all displays from one location:. Select Profiles in the monitor info line of the first display,. Select Display 1 , Display 2, or Display 3 then select the Screen you want to display.

When two displays are mounted next to each other or one above the other, a special Screen can be assigned which spans across both displays. The Screen content for these Tall and Wide Screens can then use the increased area available with two displays.

Certain windows for example: cardiac output procedure can only be shown on one display at a time. If you try to open one of these windows when it is already shown on another display, you will see a blank grey window with a cross through it. If a visitor Screen is configured for your monitor, you can use it to clear the screen of all waves and numerics but continue to monitor the patient with active alarms and trend storage at the bedside and Information Center.

You can change the name of the visitor Screen in Configuration Mode. Profiles are predefined monitor configurations. They let you change the configuration of the whole monitor so you can adapt it to different monitoring situations. The changes that occur when you change a complete profile are more far reaching than those made when you change a Screen. Screens affect only what is shown on the display. Profiles affect all monitor and measurement settings.

The settings that are defined by Profiles are grouped into three categories. These categories are:. If you are using a second display, each display can have its own individual screen selection.

When you change the profile, the screen selection configured for the new profile becomes active. These relate directly. Changes you make to any element within the settings blocks are not saved when you discharge the patient, unless you save them in Configuration Mode.

You might find it helpful to think of the three categories in terms of a restaurant menu. The Measurement Settings are like the dessert course.

From these you build your meal. Depending on your monitor configuration, when you switch on or discharge a patient the monitor either continues with the previous profile, or resets to the default profile configured for that monitor. WARNING If you switch to a different profile, the patient category and paced status normally change to the setting specified in the new profile. However some profiles may be setup to leave the patient category and paced status unchanged.

Always check the patient category, paced status, and all alarms and settings, when you change profiles. Settings or. Monitor Settings to call up a list of the settings blocks in each category. Your monitor has a default profile that it uses when you leave Demonstration, or Service modes, or when you discharge a patient. This profile is indicated by a diamond.

Some profiles are locked, so that you cannot change them, even in Configuration Mode. These are indicated by this lock symbol. Each aspect of how the monitor works and looks is defined by a setting. There are a number of different categories of settings, including,.

Screen Settings , to define the selection and appearance of elements on each individual Screen. Measurement settings , to define settings unique to each measurement, for example, high and low alarm limits. Monitor settings , including settings that affect more than one measurement or Screen and define general aspects of how the monitor works, for example, alarm volume, reports and recordings, and display brightness.

All settings are reset to the stored defaults:. Default is set to. Each measurement has a setup menu in which you can adjust all of its settings. You can enter a setup menu:. Then select the measurement name from the popup list. With this SmartKey you can access any setup menu in the monitor.